- 您现在的位置：买卖IC网 > Sheet目录323 > DV164131 (Microchip Technology)KIT STARTER PICKIT 3
PICkit? 3 User’s Guide
See Section 8.3.2 “Debugger-to-Target Communication Error Actions” .
PK3Err0047: Bootloader download failed.
See Section 8.3.3 “Debugger-to-PC Communication Error Actions” .
PK3Err0052: The current PICkit 3 hardware version %x, is out of date. This
version of MPLAB IDE will support only version %x or higher.
Did you click Cancel when asked to download the latest firmware? If so, you will
need to download it now. Select Debugger>Settings , Configuration tab, and
click Manual Download . Select the highest number .jam file and click Open .
If you cannot find any files to download or if this does not work (corrupted file),
you will need to get the latest version of MPLAB IDE and install it. Find the latest
MPLAB IDE at www.microchip.com.
PK3Err0053: Unable to get PICkit 3 protocol versions.
See Section 8.3.3 “Debugger-to-PC Communication Error Actions” .
PK3Err0054: MPLAB IDE's PICkit 3 protocol definitions are out of date. You must
upgrade MPLAB IDE to continue.
Find the latest MPLAB IDE at www.microchip.com.
PK3Err0055: Unable to set firmware suite version.
PK3Err0056: Unable to get voltages from PICkit 3.
See Section 8.3.3 “Debugger-to-PC Communication Error Actions” .
PK3Err0068: Failed while writing to boot FLASH memory.
PK3Err0069: Failed while reading boot FLASH memory.
PK3Err0070: Failed while writing peripheral memory.
PK3Err0071: Failed while reading peripheral memory.
See Section 8.3.1 “Read/Write Error Actions” .
PK3Err0073: Device is code protected.
The device on which you are attempting to operate (read, program, blank check
or verify) is code protected, i.e., the code cannot be read or modified. Check your
Configuration bits setting for code protection.
To disable code protection, set or clear the appropriate Configuration bits in code
or in the Configuration Bits window ( Configure>Configuration Bits ), according to
the device data sheet. Then erase and reprogram the entire device.
PK3Err0075: Unable to set power.
PICkit 3 cannot supply power to the target.
PK3Err0080: Failed setting shadow bit(s).
8.3
GENERAL CORRECTIVE ACTIONS
These general corrective actions may solve your problem:
DS51795A-page 44
?
?
?
?
?
?
?
Read/Write Error Actions
Debugger-to-Target Communication Error Actions
Debugger-to-PC Communication Error Actions
Corrupted Installation Actions
USB Port Communication Error Actions
Debug Failure Actions
Internal Error Actions
? 2009 Microchip Technology Inc.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DV164132
KIT EVAL F1 FOR PIC12F1/PIC16F1
DV243003
KIT STARTER FOR SRL MEM PRODUCTS
DVA1001
ADAPTER FOR PIC16F716 18DIP
DVA1004
DEVICE ADAPTER 8/14/20DIP
E3R-D12GP-P
RELAY RCVR PLUG-IN DIMMER
E3R-R12-3HOTP
RCVR 3WIRE RELAY 120V
E3R-R12GP
RCVR PLUG-IN RELAY
E3T-MICFP-40
CONVERTER 4-CH SLT SENSOR
相关代理商/技术参数
DV164131
制造商:Microchip Technology Inc 功能描述:PICKIT 3 DEBUG EXPRESS
DV164131-XLP
制造商:Microchip Technology Inc 功能描述:KIT DEV PICKIT 3-XLP/NANOWAT
DV164132
功能描述:开发板和工具包 - PIC / DSPIC F1 Evaluation Kit RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DV164132
制造商:Microchip Technology Inc 功能描述:PIC12F1xxx/PIC16F1xxx F1 Evaluation Kit
DV164133
功能描述:电源管理IC开发工具 Energy Harvesting Development Tool
RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
DV164136
功能描述:开发板和工具包 - PIC / DSPIC PIC18F DEV Kit (with PICkit 3) RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DV164139
功能描述:开发板和工具包 - PIC / DSPIC Lo PIn Count USB Dev Kit (w/PICkit 3) RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DV17K3225T
制造商:SEI Stackpole Electronics Inc 功能描述:- Tape and Reel 制造商:SEI Stackpole Electronics Inc 功能描述:Var MOV 17VAC/22VDC 100A 27V 3225 SMD T/R